Did You Know...
-
MTC recommends that you get the tire spinning with the…Read more...
-
MTC does not recommend this practice; it introduces excessive heat…Read more...
-
Tightening the anodized nuts will raise the RPM at which…Read more...
-
MTC Engineering uses a special high strength aluminum alloy containing…Read more...
-
You should avoid this if at all possible, if the…Read more...
-
The most common causes of broken fiber plates are improper…Read more...
-
.720” for the Regular Stall SpringsRead more...
.525” for the Medium… -
If your bike is lazy or is driving through the…Read more...
-
Our billet inner hub eliminates the back torque limiter on…Read more...
-
MTC Engineering is open Monday - Friday 8 am -…Read more...
-
The Hayabusa billet inner hub comes with: Heavy duty springs.…Read more...
-
If your bike is too aggressive, then you need to…Read more...
-
Turn the piston upside-down and measure width of the bottom…Read more...
-
For proper operation MTC Engineering recommends an air gap of…Read more...
- Read more...
-
78mm is the largest. For larger, you must go to…Read more...
-
Yes, while you should be able to shift the bike normally…Read more...
-
It depends on the lockup type.Read more...
Reducing the arm weight… -
There can be a few things that cause this, however, the most…Read more...
-
Absolutely not! Backing the studs out allows the possibility for…Read more...
-
We do not have forgings for every piston size. We…Read more...
-
MTC recommends the use of our Slider Shim Kit for…Read more...
-
The best method to check the endplay is to use…Read more...
-
Some of the applications can be upgraded, but others cannot…Read more...
-
You can try running stiffer springs to keep your clutch from burning…Read more...
-
Yes.Read more...
This is a very common set-up to gain… -
You need to measure the OD (Outside Diameter) of your…Read more...
-
MTC was derived from the first initial of the last…Read more...
-
1. Turn piston over and measure bottom of the skit.…Read more...
-
The MTC Engineering dealer program is for licensed businesses that…Read more...
-
MTC recommends an oil no heavier than 10w30 for use with…Read more...
-
For best results, MTC recommends setting the 2-step box about…Read more...
-
All of MTC's products are available direct or through our…Read more...
-
You need to measure each ring groove with a set…Read more...
-
We would be honored. We appreciate your endorsement of our…Read more...
-
Having the correct basket endplay is very important. The nature…Read more...
-
Heavy-duty cylinder studs torque to 40-42 ft lb....Read more...
-
Install degree wheel and find TDC with a positive stop.…Read more...
-
Piston to cylinder fit is critical. Some applications…Read more...
-
The first thing to do is to remove the screw…Read more...
-
DO NOT OIL RINGS!Read more...
By not… -
You MUST use a thread locking compound or use a…Read more...
-
You can adjust your MTC slider's stall speed to work…Read more...
-
MTC Engineering accepts the following payment methods: Visa, Master Card,…Read more...
-
A Slider Clutch comes standard with Regular Stall Springs, unless…Read more...
-
The slider shims are to be installed AFTER the 3pc…Read more...
-
There are a number of things that can affect your…Read more...
-
Certainly! We can build your lockup with one of our turbo baselines if…Read more...
-
Yes.Read more...
Since MTC Engineering is the sole source provide for… -
No. You must also replace the sleeve next to it at…Read more...
-
Do NOT do dry hops with a slider, shocking the…Read more...
-
Yes, in addition to the multistage springs included with your lockup…Read more...
-
Can I adjust the set screws on the top of…Read more...
-
MTC recommends there be .100-.125" clearance between the flat surface…Read more...
-
Absolutely! If you include stats about your application with your…Read more...
-
MTC has three types of systems available. O-ring machined into…Read more...
-
Yes. OEM fibers and steels can be used with MTC…Read more...
-
Installing Wire LocksRead more...
Install the end of one lock at… -
Nearly all MTC fiber plates have a larger surface area…Read more...
-
Not really, however the slider springs must be under some…Read more...
-
The chart shows what you need to send depending on…Read more...


















